Bright, indirect light to filtered sun.

Allow the soil to dry out completely between waterings.

Enjoys moderate to high levels of humidity. Spritz occasionally.

Ideally, the Money Tree likes the room temperature at 72°F. They handle warmth rather than cold so keep them away from cold drafts.

Outside: Grow in morning light, partial shade (4-6 hours) where nights are above 45°F.

Indoors: The Money Tree prefers bright, indirect light for at least six hours in a southern, eastern and western windows.

Fertilize bimonthly during their growing period. Use a balanced liquid fertilizer at 1/2 strength. Reduce during the fall and winter months while the plant is in their dormant phase and refrain from watering as much so they can rest.

When receiving the plant, do not repot immediately but wait at least 6-12 months or if the roots are beginning to get crowded and growing through the drainage holes.

Repot in the spring, using a 2" bigger pot to keep the roots drier. (Too big of a pot could cause the soil to dry slower, which is not helpful.) Use a well-draining indoor potting mix with perlite to help with drainage. Water your plant in the old pot before transferring over and let sit an hour. Place a piece of screening at the bottom of the container over the drainage hole to secure the soil and allow to drain.

Add soil to the bottom to elevate the root ball. Lift the plant and release the roots against the existing planter. Use a clean knife or garden trowel to wedge between the pot and the soil to loosen. Inspect the root ball. Notice if there are any dead or rotting roots and trim off with sterile pruners. If the plant is rootbound, cut through the roots to alleviate continued encircling. Ensure the plant is sitting about 1" below the edge of the pot to avoid water spillage. Add more soil and backfill around the sides by tamping down. Fill up to the soil line but not over. Water thoroughly, leaving the soil damp but not soggy. If settling occurs, add more soil.

Prune the leaves to stimulate new growth by cutting in front of a leaf node. Trim off any dead or damaged stems to keep them healthy.

Stem Cutting: In early summer, take a stem cutting, use sharp pruners to remove a cutting from a tip off the vine. Cut at least 4-6 inches of stem to propagate. Place in a vase with water to root. Change the water each week with filtered, bottled, or tap water sitting at least 24 hours. After 3-4 weeks, check to make sure the stem has 1-2 inch, well-formed roots. If so, it is time to plant. *Fill a small container with drainage holes (too large of a container for the cutting will make it challenging to regulate watering needs) using an indoor well-draining potting mix. Mix a little rooting hormone into the soil. Poke a hole in the soil with a pencil. Then, place the cutting in the hole and tamp the soil down around them. Water the plant and keep them in medium to bright indirect sunlight. After 4-6 weeks, the roots should establish.

Medium to bright indirect light. Never direct sunlight.

Don't overwater. Too much water can cause root or crown rot.

Enjoys high humidity. Spritz occasionally.

Ideally, the Bromeliads grow best when temperatures are between 60°-80°F.

Outside: Grow in partial shade (4-6 hours) where nights are above 60°F.

Indoors: The Bromeliad prefers bright, indirect light for at least six hours in a southern, eastern and western windows.

Fertilize monthly during their growing period while the flower is in bloom with a balanced liquid fertilizer and a time release granular soil fertilizer. Reduce during the fall and winter months while the plant is in their dormant phase. When fertilizing, don't get the fertilizer in the urn or tank as this can burn the plant.

To repot a bromeliad grown out of their container, get a larger one that's 2 inches wider with drainage holes. Make sure the container is sturdy enough if the bromeliad is top-heavy.

Use a mixture of 1/2 well-draining potting mix, 1/4 perlite, and 1/4 orchid bark. Place a piece of screening at the bottom of the container over the drainage hole to secure the soil and allow to drain. Fill the container's bottom with the mix, then place the bromeliad in and fill around the edges. Leave at least an inch of room from the top of the container to avoid water spillage.

Water the plant well. Add them to an area with bright, indirect sunlight and humidity to let them settle into their new environment.

Remove the dead or dying part with some pruners back to the base. This simple pruning will give more light to the remaining pups with more room to stretch and make new baby bromeliads.

To propagate the bromeliad pups, let the pups grow on the mother plant until they reach at least 5 inches or a third of the original stalk's size. Take the mother plant out of the pot. Cut the mother plant top off to see the pup and remove all the dead leaves. Pull away the pup and the small root system with them. You may need to use pruners to help remove the roots and pup. Some arm strength may be required to wedge them away from the parent plant. Once you have them separated, you can use a bromeliad medium (1/2 well-draining potting mix, 1/4 perlite, and 1/4 orchid bark) to repot them in. Use a container with drainage holes and nothing too big for the pup. Allow at least 2 inches of soil to surround the pup. You will bury the roots very shallow in the soil so as not to cause rotting on the leaves. Tamp the mix down to secure the plant. Water from overhead to give them a drink and water well so it drains through the hole. Set in a bright, indirect sunny area.